宽窄相间河道水流紊动特性试验研究          下载免费PDF全文

王文娥  廖伟  漆力健 《水科学进展》2020,31(3):394-403

为了探索宽窄相间河道的水流紊动特性,以西南地区宝兴河上游宽窄相间河段为研究对象,基于室内概化模型试验,采用多普勒声学流速仪(ADV)测量了室内模型典型断面上的三维瞬时流速,分析典型断面上的纵向时均流速、紊动强度、雷诺切应力和紊动能的分布规律。试验结果显示:宽窄相间水槽中,扩散段边壁的紊动强度大于中心区域的紊动强度,最大值位于0.2倍水深处;扩散段两侧坡脚处紊动能最大;侧壁区的平面和立面雷诺切应力最大值出现在扩散段内,中心区域最大雷诺切应力位于两槽间的中间断面处;扩散段内水流紊乱,两侧出现旋涡和涡脱,易造成侧壁侵蚀加强,引起河道拓宽。深入分析了宽窄相间河道水流的紊动特性,可为山区河流治理和自然灾害防治提供参考。  相似文献   

淹没植物明渠床面冲淤及其对水流运动的影响          下载免费PDF全文

赵汗青  唐洪武  闫静  戴会超  刘志武 《水科学进展》2021,32(2):250-258

植物的存在改变了河流水动力特性,造成独特的床面冲淤态势。利用实验室水槽模拟含淹没植物的河道,对床面形态和紊流统计特性参数进行测量,研究不同类型紊流作用下的床面冲淤特征以及床面起伏对流动的影响。结果表明:床面剪切紊流条件下,床面形态为马蹄坑-沙沟/沙脊与沙波复合分布,床面变形加剧了流速沿水深不均匀分布并促进水流动量交换;在自由剪切混合层紊流条件下,床面形态为植物根部马蹄形冲坑及其后方沙沟、沙脊交错分布,床面变形对流动的影响并不显著;“类二重紊流”条件下,床面形态同样表现为马蹄坑-沙沟/沙脊-沙波复合,床面变形促进植物层内部的水流动量交换、抑制紊动清扫,抑制植物层外部的动量交换、促进紊动喷射。  相似文献   

双偏振天气雷达水平和垂直通道回波对比     

何田勇  胡明宝  艾未华  陈楠 《气象科学》2019,39(3):368-376

本文针对南京溧水S波段双偏振多普勒天气雷达获取的回波I/Q信号,采用FFT算法处理水平和垂直通道I/Q数据,分别得到水平和垂直通道回波的强度、速度值,定性分析了两通道回波强度、速度数据差异,引入平均差及均方根误差参数做定量分析。对比结果表明:两通道I/Q数据处理得到的回波层次分布基本一致;两通道速度数据差异较小,强度数据差异较大。以水平通道回波数据为基准,当回波强度小于16 dBz时,水平通道强度偏小,这可能是由云系边缘较小的针状冰晶所致;当回波强度大于32 dBz时,水平通道强度值偏大,且随回波强度的增加两通道强度差值增大,这反映了强降水中大粒子较多,而粒子越大,降落过程中扁平程度越大;两通道回波强度的差值与回波强度大小呈现一定相关性,这可能反映了单偏振天气雷达在定量测量降水中精度不高,通过双偏振雷达联合利用两通道数据有望改善雷达定量测量降水精度,提升雷达定量估测降水能力。  相似文献   

初始孔压非均布下一维地基砂垫层优化研究     

蒙宇涵  陈征  冯健雪  李红坡  梅国雄 《岩土力学》2019,40(12):4793-4800

针对吹填土地基水平排水砂垫层铺设深度优化问题,建立了初始孔压非均布下含砂垫层地基的一维固结模型,利用有限Fourier正弦变换法得出了超静孔压和地基整体平均固结度的解答并通过退化验证了解答的正确性。采用二分法分析了砂垫层的最优铺设深度随时间的演化规律,给出了砂垫层最优铺设深度与时间的关系图。研究表明：在固结初期,砂垫层宜放置在土中初始超静孔压较大的位置;在固结后期,砂垫层的最优设置深度为土体厚度的2/3（单面排水）或者1/2（双面排水）的位置。以预压地基平均固结度达到90%所需时间最短为例,当初始孔压倒三角形、正三角形与梯形分布时,单面排水条件下,应分别在0.52、0.72、0.62倍地基土深度处设置砂垫层;双面排水条件下,应分别在0.42、0.58、0.46倍地基土深度处设置砂垫层。最后通过算例分析了当地基土中砂垫层采用最优铺设深度时,与在中间位置铺设砂垫层、不设砂垫层的情况分别进行对比,当时间因子取0.09时,地基土平均固结度分别提高6%和54%。  相似文献   

Multi‐scale analysis of a migrating submarine channel system in a tectonically‐confined basin: The Miocene Gorgoglione Flysch Formation,southern Italy     

Claudio I. Casciano  Marco Patacci  Sergio G. Longhitano  Marcello Tropeano  William D. McCaffrey  Claudio Di Celma 《Sedimentology》2019,66(1):205-240

The Miocene Gorgoglione Flysch Formation records the stratigraphic product of protracted sediment transfer and deposition through a long‐lived submarine channel system developed in a narrow and elongate thrust‐top basin of the Southern Apennines (Italy). Channel‐fill deposits are exposed in an outcrop belt approximately 500 m thick and 15 km long, oriented oblique to the palaeoflow, which was roughly south‐eastward. These exceptional exposures of channel‐fill strata allow the stacking architectures and the evolution of the channel system to be analyzed at multiple scales, enabling the effects of syn‐sedimentary thrust tectonics and basin confinement on the depositional system development to be deciphered. Two end‐member types of elementary channel architecture have been identified: high‐aspect‐ratio, weakly‐confined channels, and low‐aspect‐ratio, incisional channels. Their systematic stacking results in a complex pattern of seismic‐scale depositional architectures that determines the stratigraphic framework of the deep‐water system. From the base of the succession, two prominent channel complex sets have been recognized, namely CS1 and CS2, consisting of amalgamated incisional channel elements and weakly‐confined channel elements. These channelized units are overlain by isolated incisional channels, erosional into mud‐prone slope deposits. The juxtaposition of different channel architectures is interpreted to have been governed by regional thrust‐tectonics, in combination with a high subsidence rate that promoted significant aggradation. In this scenario, the alternating ‘in sequence’ and ‘out of sequence’ tectonic pulses of the basin‐bounding thrusts controlled the activation of coarse‐clastic inputs in the basin and the resulting stacking architectures of channelized units. The tectonically‐driven confinement of the depositional system limited the lateral offset in channel stacking, preventing large‐scale avulsions. This study represents an excellent opportunity to analyze the stratigraphic evolution of a submarine channel system in tectonically‐active settings from an outcrop perspective. It should find wide applicability in analogous depositional systems, whose stratigraphic architecture has been influenced by tectonically‐controlled lateral confinement and associated lateral tilting.  相似文献   

伶仃洋茅洲河口滩槽演变水沙模拟及治导线优化          下载免费PDF全文

陆永军  莫思平  王志力  季荣耀  顾继一 《水科学进展》2019,30(6):770-780

为适应伶仃洋茅洲河口治理开发条件,以保证行洪顺畅为泄洪纳潮的首要原则,同时顺应水沙运动和河势发展规律,对河口进行治导线比选和优化。该河口治导线方案分单、双通道,两类通道不同扩宽率下设计有围填、围填加开挖2种方案,开展水动力泥沙数学模拟计算和物理模型试验。结果表明:河口治导线各方案对伶仃洋涨、落潮流速的影响范围主要集中在交椅湾及其附近海域;方案实施后,周边海区冲淤变化较小,未对河势造成不利影响;根据对水动力、河口泄洪、河势稳定影响的综合分析,单双通道相比较而言,对洪水位、纳潮量、高低潮位、流速、河床冲淤的影响规律具有较好的一致性,相同扩宽率下各方案的影响程度均在同量级。  相似文献   

腹板开槽冷弯薄壁卷边槽钢抗火性能有限元分析模型     

马奇杰  王培军  郑英杰 《地震学刊》2012,(2):205-209

位于冷弯薄壁型钢构件腹板的槽孔,可延长构件两边的热量传递路线,减弱冷弯薄壁钢构件作为墙板龙骨引起的冷桥效应。常温下冷弯薄壁构件的屈曲破坏模态已非常复杂,包括整体屈曲、局部屈曲和畸变屈曲等,且不同的屈曲破坏模态可能会相互影响。火灾下冷弯薄壁构件的破坏机理将更为复杂,根据常规的稳定理论难以求解其火灾下的临界荷载。本文利用有限元方法对火灾下腹板开槽冷弯薄壁卷边槽钢的受力性能进行了模拟,研究了单元类型、材料模型、初始几何缺陷以及求解方法等因素对分析结果的影响,为同类构件抗火性能的有限元模拟分析提供了建模依据。  相似文献   

The stratigraphic record and processes of turbidity current transformation across deep‐marine lobes          下载免费PDF全文

Ian A. Kane  Anna S. M. Pontén  Brita Vangdal  Joris T. Eggenhuisen  David M. Hodgson  Yvonne T. Spychala 《Sedimentology》2017,64(5):1236-1273

Sedimentary facies in the distal parts of deep‐marine lobes can diverge significantly from those predicted by classical turbidite models, and sedimentological processes in these environments are poorly understood. This gap may be bridged using outcrop studies and theoretical models. In the Skoorsteenberg Formation (South Africa), a downstream transition from thickly bedded turbidite sandstones to argillaceous, internally layered hybrid beds, is observed. The hybrid beds have a characteristic stratigraphic and spatial distribution, being associated with bed successions which generally coarsen and thicken‐upward reflecting deposition on the fringes of lobes in a dominantly progradational system. Using a detailed characterization of bed types, including grain size, grain‐fabric and mineralogical analyses, a process‐model for flow evolution is developed. This is explored using a numerical suspension capacity model for radially spreading and decelerating turbidity currents. The new model shows how decelerating sediment suspensions can reach a critical suspension capacity threshold beyond which grains are not supported by fluid turbulence. Sand and silt particles, settling together with flocculated clay, may form low yield strength cohesive flows; development of these higher concentration lower boundary layer flows inhibits transfer of turbulent kinetic energy into the upper parts of the flow ultimately resulting in catastrophic loss of turbulence and collapse of the upper part of the flow. Advection distances of the now transitional to laminar flow are relatively long (several kilometres) suggesting relatively slow dewatering (several hours) of the low yield strength flows. The catastrophic loss of turbulence accounts for the presence of such beds in other fine‐grained systems without invoking external controls or large‐scale flow partitioning and also explains the abrupt pinch‐out of all divisions of these sandstones. Estimation of the point of flow transformation is a useful tool in the prediction of heterogeneity distribution in subsurface systems.  相似文献   

Sequence architecture and depositional evolution of the Late Miocene to quaternary northeastern shelf margin of the South China Sea     

《Marine and Petroleum Geology》2017

Based on an integrated analysis of seismic, well logging and paleontological data, the sequence architecture and depositional evolution of the northeastern shelf margin of the South China Sea since Late Miocene are documented. The slope deposits of the Late Miocene to Quaternary can be divided into two composite sequences (CS1 and CS2) bounded by regional unconformities with time spans of 3–7 Ma, and eight sequences defined by local unconformities or discontinuities with time spans of 0.8–2.3 Ma. Unconformities within CS1 feature shelf-edge channel erosion, while in CS2 they form truncations at the top of the shelf margin as prograding complexes and onlap contacts against the slope.Depositional systems recognized in the slope section include unidirectionally migrating slope channels, slope fans or aprons, shelf-edge deltas and large-scale slope clinoforms. CS1 (Late Miocene to Pliocene) is characterized by development of a series of shelf-margin channels and associated slope fan aprons. The shelf-margin channels, oriented mostly NW-SE, migrate unidirectionally northeastwards and intensively eroded almost the entire shelf-slope zone. Two types of channels have been identified: (1) broad, shallow and unconfined or partly confined outer-shelf to shelf-break channels; and (2) deeply incised and confined unidirectionally migrating slope channels. They might be formed by gravity flow erosion as bypassing channels and filled mostly with along-slope current deposits. Along the base of the shelf slope, a series of small-scale slope fans or fan aprons are identified, including three depositional paleo-geomorphological elements: (1) broad or U-shaped, unconfined erosional-depositional channels; (2) frontal splays-lobes; and (3) non-channelized sheets. CS2 (Quaternary) consists mainly of a set of high-angle clinoforms, shelf-margin deltas and lower slope unidirectionally migrating channels.The relative sea level changes reflected in the sequence architecture of the study area are basically consistent with Haq's global sea level curve, but the development of regional unconformities were apparently enhanced by tectonic uplift. The development of high-angle (thick) clinoforms in the Quaternary may be attributed to a high sediment supply rate and rapid tectonic subsidence. The formation of the unidirectionally migrating channels appears to have resulted from the combined effects of the northeastward South China Sea Warm Current (SCSWC) and downslope gravity flow. The formation of the slope channels in the outer-shelf to shelf-break zone may be predominately controlled by bottom current, whereas those developed along the middle to lower slope zone may be dominated by gravity flow.  相似文献   

Simulations of measures to control lava flows     

Eisuke Fujita  Masataka Hidaka  Akio Goto  Susumu Umino 《Bulletin of Volcanology》2009,71(4):401-408

We evaluated the quantitative effects of artificial barriers, water-cooling and guiding channels on lava flow using the lava simulation program LavaSIM. Lava flow is basically subject to the topography around the path, effusive rate and viscosity. To prevent damage due to lava flow, we conducted experiments in controlling the flow direction, velocity and temperature. The simulation demonstrated that artificial barriers can successfully change the direction of a lava flow and is more effective when placed nearly parallel to the flow direction at a point where the topography is not very steep, while a barrier placed perpendicular to the flow direction can only stop the flux temporarily, ultimately allowing the solidified crust to accumulate and causing the following mass to go over the barrier. The water-cooling trial was also effective in controlling the direction and temperature, although the amount of water was as much order as 10⁵ m³. The guiding channels successfully control the direction and inundated area but only in local areas.  相似文献